Troubleshooting
| Problem | Solution |
| My Board is taking on water. |
Though EPP foam boards will take on a small amount of water, there should not be an excess of water absorbed during a session. If you can hear water sloshing around inside of your board, and the weight/ balance point is being drastically affected, your board may be defective. This potential issue is caused by a defect in the manufacturing process. The process has been changed to reduce the likelihood of this defect moving forward. |
| My remote has stopped working |
Make sure that your remote is properly charged. If the remote will not charge, and/or there is water inside of the remote, please contact your dealer for a replacement. |
| My board is running without remote connection |
Upgrade your firmware to the latest version: |
| Fuselage has broken without impact (no crash, drop, etc.) | Some of the early productions may have been effected by a bad batch of alloy. As a result, some customers have experienced broken fuselages under normal usage. These breakages are covered under your waydoo warranty. The design has been improved to reduce the likely hood of this defect moving forward. |
| Board turning off randomly (turns back on when pressing power button) |
The magnet in the board may not me making a solid connection with the battery See magnet video |
| Red battery fault light | Check if the temperature of the battery is too high. If the temperature is too high, stop using it and wait for the battery to cool down before continuing to use. Check whether the battery level is too low. If the battery is too low, charge immediately. If the problem is still not solved, contact after-sales service in time. |
| Battery has no power | Check whether the power assembly and the battery are properly connected. If there is any looseness, tighten the L-shaped bolts in time. Normally, the battery has output. The output indicator on the display will continue to light up in blue. |
| Battery cannot be charged | First, check whether the fault indicator of the battery is on. If it is, contact the after-sales service to repair or replace the battery, Next, check whether the charger indicator is flashing red. If the charger is in good condition, check whether the AC plug of the charger and the integrated battery port are properly connected. Tighten if they are loose. If the connection is normal, turn the charger over. Make sure the rocker switch of the electrical appliance is in the ON position and then the battery should be able to charge normally. |
| Motor making abnormal noise during use | Immediately release the trigger of the remote control to stop the motor, turn off the remote control, lay on the board, and paddle back to land using your hands. Take out the battery and check whether there is any foreign matter in the propeller. If there is foreign matter, remove the propeller protective cover and the propeller for cleaning. Before inspecting the propeller, make sure that the battery is disconnected and remove the battery. |
| Motor not turning during use | Immediately release the trigger of the remote control to stop the motor, turn off the remote control, and lay on the board and paddle back to land using your hands. Check whether the status indicator of the remote control shows normal connection status. Next, check whether the battery level is normal, and then check whether the powertrain and the board are loose. If it is loose, tighten it in time. If the problem is not solved after attempting the above steps, remove the battery and check whether sea water has seeped into the metal joints or if there is any corrosion. If the above situation has occurred, rinse the plug with fresh water and dry it with a rust remover to remove the rust on the metal joints. Finally, wash and dry the plug |
| Shaking or vibrating while riding | Immediately release the trigger of the remote control to stop the motor, turn off the remote control, lay on the board, and paddle back to land using your hands. Remove the battery and check whether the mounting bolts of the power assembly are loose. If loose, tighten them in time. |
The remote control connection appears intermittent during use |
Immediately release the trigger of the remote control to stop the motor, turn off the remote control, lay on the board, and paddle back to land using your hands. Turn on the remote control and check whether the Bluetooth icon is flashing. If it is flashing, restart the battery and pair again using Bluetooth. If the problem is still not resolved, contact after-sales service in time. |
Remote fault codes |
“Err.1” = Angle sensor initialization failed. “Err. 2” Spiflash initialization failed. “Err. 3” = Angle sensor and spiflash initialization failed. “Err. 4” = GPS failed. “Err. 7” = Angle sensor initialization, spiflash initialization, and GPS failed. |
Still having trouble?